页次: 1
Dell G5 5590
显卡为GTX1650的版本
在安装完archlinux后无法外接屏幕,表现是能识别外接屏幕,能设置双屏,但是扩展屏幕没有任何内容,只有鼠标,能将窗口拖过去但是无法显示。
在尝试包括但不限于“更换开/闭源驱动”、“安装nvidia-prime”、“配置xorg.conf”后均无果。
突发奇想,在AUR源中下载了mhwd,使用mhwd安装了video-hybrid-intel-nvidia-dkms-prime-render-offloading驱动,无法双屏的问题奇迹般解决。
这时出现了第二个问题,当笔记本设置为“仅笔记本屏幕”、“向左拓展”、“向右拓展”时,没有任何异常,但当设置为“仅拓展屏幕”时,一切都开始卡顿(除了鼠标)。当然,此时画面仅在外接屏幕显示,切换画面是没有问题的。
目前尝试了KDE与xfce4,表现均为上述效果。
xrandr --listproviders
Providers: number : 2
Provider 0: id: 0x45 cap: 0xf, Source Output, Sink Output, Source Offload, Sink Offload crtcs: 3 outputs: 3 associated providers: 1 name:modesetting
Provider 1: id: 0x241 cap: 0x2, Sink Output crtcs: 4 outputs: 1 associated providers: 1 name:NVIDIA-G0
------
xrandr
Screen 0: minimum 320 x 200, current 5759 x 2160, maximum 16384 x 16384
eDP-1 connected 1920x1080+0+0 (normal left inverted right x axis y axis) 344mm x 194mm
1920x1080 60.06*+ 60.01 59.97 59.96 59.93 48.04
1680x1050 59.95 59.88
1400x1050 59.98
1600x900 59.99 59.94 59.95 59.82
1280x1024 60.02
1400x900 59.96 59.88
1280x960 60.00
1440x810 60.00 59.97
1368x768 59.88 59.85
1280x800 59.99 59.97 59.81 59.91
1280x720 60.00 59.99 59.86 59.74
1024x768 60.04 60.00
960x720 60.00
928x696 60.05
896x672 60.01
1024x576 59.95 59.96 59.90 59.82
960x600 59.93 60.00
960x540 59.96 59.99 59.63 59.82
800x600 60.00 60.32 56.25
840x525 60.01 59.88
864x486 59.92 59.57
700x525 59.98
800x450 59.95 59.82
640x512 60.02
700x450 59.96 59.88
640x480 60.00 59.94
720x405 59.51 58.99
684x384 59.88 59.85
640x400 59.88 59.98
640x360 59.86 59.83 59.84 59.32
512x384 60.00
512x288 60.00 59.92
480x270 59.63 59.82
400x300 60.32 56.34
432x243 59.92 59.57
320x240 60.05
360x202 59.51 59.13
320x180 59.84 59.32
DP-1 disconnected (normal left inverted right x axis y axis)
HDMI-1 disconnected (normal left inverted right x axis y axis)
HDMI-1-0 connected primary 3840x2160+1919+0 597mm x 336mm
3840x2160 60.00*+ 59.94 50.00 30.00 29.97 25.00 23.98 23.98
2560x1440 59.95
2048x1280 59.92
2048x1152 60.00
1920x1200 59.88
1920x1080 60.00 59.94 50.00
1680x1050 59.95
1600x1200 60.00
1280x1024 75.02 60.02
1280x800 59.81
1280x720 59.94 50.00
1152x864 75.00
1024x768 75.03 60.00
800x600 75.00 60.32
720x576 50.00
720x480 59.94
640x480 75.00 59.93 59.94
1680x1050 (0x4c) 146.250MHz -HSync +VSync
h: width 1680 start 1784 end 1960 total 2240 skew 0 clock 65.29KHz
v: height 1050 start 1053 end 1059 total 1089 clock 59.95Hz
1280x1024 (0x53) 108.000MHz +HSync +VSync
h: width 1280 start 1328 end 1440 total 1688 skew 0 clock 63.98KHz
v: height 1024 start 1025 end 1028 total 1066 clock 60.02Hz
1280x800 (0x5d) 83.500MHz -HSync +VSync
h: width 1280 start 1352 end 1480 total 1680 skew 0 clock 49.70KHz
v: height 800 start 803 end 809 total 831 clock 59.81Hz
1024x768 (0x64) 65.000MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.36KHz
v: height 768 start 771 end 777 total 806 clock 60.00Hz
800x600 (0x73) 40.000MHz +HSync +VSync
h: width 800 start 840 end 968 total 1056 skew 0 clock 37.88KHz
v: height 600 start 601 end 605 total 628 clock 60.32Hz
640x480 (0x80) 25.175MHz -HSync -VSync
h: width 640 start 656 end 752 total 800 skew 0 clock 31.47KHz
v: height 480 start 490 end 492 total 525 clock 59.94Hz
离线
+1
离线
遇见同样的问题,但我并未使用mwhd. 笔记本配置为3060,采用NVIDIA闭源驱动。在hybrid模式下,用hdmi输出(连接到3060)的外接显示器如果是“仅外接显示”输出会非常卡顿,如果同时开启笔记本内屏就正常了。目前我的解决方案是 https://wiki.archlinux.org/title/NVIDIA … phics_only 设置采用NVIDIA显卡渲染xorg.
离线
同样的问题,intel 与 nvidia 双显卡笔记本,使用 nvidia 驱动外接显示器时只有在移动光标是外接显示器才刷新。
解决方案如下:
https://bbs.archlinux.org/viewtopic.php?id=284651
Archの世界へ転生して、Lv0の勇者
离线
我的也是这种情况,显卡是1050,之前解决过这个问题,我记得是用一个软件模拟的独显直连然后就解决了
离线
页次: 1